Let’s go one by one.
- obdstar F108+review
The obdstar tool F108+ works well.
obdstar F108+ feedback on what work:
OBDSTAR F108+ is good and safe PSA PIN CODE reading tool, fast read pin code via OBD.
Hardware check = OK
P/C/DS ver: 31.20
Tested OBDSTAR F108+ read pin with working key:
Citroen ds3 2013- ok
Citroen picaso 2009- ok
Peugeot 207sw 2004- ok
Peugeot 407 2004-ok
Peugeot 307 2005- ok
2010 C4 picasso
2012 308 read pin code within 6-7 minutes. all fine.
207 2009. Need igntion On – OFF 10 times in 7mn. Pin read succesful.
Peugeot 208 2013, very fast. Only ignition OFF – ON 1 time and it give pincode.
C3 2014 Valeo BSI, one time OFF ON and give pincode.
Peugeot 307 2008 pin code read-ok
Citroen C5 FAST-OK
307 CAN > 2005
PIN CODE OK , 4/5 minute
Tested on PEUGEOT 307 , year 2006
Peugeot 207 -07: about 7mn
Jumpy – 08/09: about 6mn.
(All for additional key. Use pin and program with X100+. )
Citroen Picasso 2006, r`eading pin OK
Citroen C3 , Engine 9HZ, year 2005, reading PIN = OK
Peugeot 207 , Engine 9HZ , year 2006, reading PIN = OK
-> I have extracted pin from over 20 cars, all fine. Not necessary to connect charger to car as it doesn’t put Bsi in service mode like psa bsi tool, or avdi where windscreen wipers would activate etc. On average 5 to 8 minutes, although a 508 and a 2008 I did it found code almost instantaneously.
-> “F108+” LAST UPDATE V31.20 positive feedback:
tested on 2004 Citron C4 , PIN code retrieve less of 4 minutes , verified with Diagbox
Diagbox ( in french “same PIN code registered inside BSI” )
PCB Full chip
I plug on OBD2 and F108+ sniffing “kwp fast”traffic , i turn ignition “on/of” 10 times / 4 minutes
2004 C4 / this car is not CAN ! CAN protocol is after 2008 on PSA car , some user say NO HE CAN’T , but yes we can !
I’m sure full chip PCB F108+ with last update can retrieve all PIN code , it’s the same BSI for PSA ( Siemens , Valeo & J-C ) .
And if it’s not FULL CHIP tool F108+ , CONNECTION BREAK DOWN , k-line is not operational .
Thanks TERMINATOR1000 & Duracell2’s experience share (DK member)
– Citroen C3 AirCross 2017, hitag AES 128bits. Get pin just one time OFF/ON
Citroen C3 2014, CE0523 FSK, get pin also one time OFF/ON.
So it is very fast for PSA newer car 2017.
Note: I get pin with F108. Program with SKP900.
– Citroen c4 2005 can-jc pin ok
– Peugeot Partner 2011 , PIN code retrieving in 5 seconds !!! 2 Key programming less than 1 minute ….
– F108+ cost 110€ ! & pin code 3€ ( car before 2006, someone test ok on 2017 year ) , more than 100 success key programmed !
F108+ over the top
-Peugeot 308 ( 2008- ) , PIN retrieve less than 6 MINUTES , 2 Key programming OK ( ASK 2BT CE0523 PCF7941 )
More OBDSTAR F108+ FAQ:
- Update onlineonly by micro SD card , 1 year free access after registration , serial number + dealer ID for registration : “OBDSTAR UpgradeTools”
- Is it true: The device just can support the car after 2008 year and the car which is CAN Protocol.?
Answer: No, FAKE NEWS , my report prouve that F108+ support “no-CAN” car before 2008 …. I’m suppose they advertise old F108 support the car after 2008 year and the car which is CAN Protocol
Many bad feedback on forum , i’m not OBDSTAR seller , but 1 test 1 PIN !
Sure for the other buyers of F108 without chip , it’s sad , PCB is incomplet K-LINE is unplug ! no miracle …
So i have just used this little device for reading pin codes and so far 100% success. Personally I would recommend it to anyone thinking of buying one as its cost is low and 1-2 keys pays for it already.
Reliable source of OBDSTAR F108+ at best price:
F108 is stop producing. H108 is highly recommend.
- OBDSTAR H108
obdstar H108 is 2018 new one, can do both Citroen / Peugeot pin reading as well as mileage adjustment. It can fully replace F108 and it has more advantages than F108.
obdstar H108 is better than F108+ in the following aspects:
- VVDI 2 reads pin code for Citroen / Peugeotprocedure
VVDI2 PSA software is really a good tool for reading Citroen Peugeot pin code.
Step 1: Open VVDI2 Quick Start, click on the “Peugeot” icon, connect VVDI2 programmer to the PC and Peugeot / Citroen.
Step 2: Click on “Read Pin code”, and receive message “Turn on ignition”.
Each time switch ON ignition, switch OFF/ON times will increase 1
if the times not increase, please switch OFF ignition again, take key off ignition switch, wait above 10 seconds, then switch ON.
Repeat this procedure until the switch OFF/ON times increase 1.
Step 3: VVDI2 Read out pin code successfully
- OBDSTAR X300 PRO3 /
- read PSA pin codefor free
OBDSTAR PSA pin code reading features in: Auto identify ECU model and read Pin code for free.
SIEMENS D76F0018+95160 K LINE(BSI-E0X-00/BSI-F0X-00)
CONTINENTAL SC667050+95256 CAN(BSI-Q0X-00)
JC easyCAN4+29LV400BB+95128 CAN (BSI2004-H0X)
JC easyCAN4F1M-32+95128 CAN (BSI04EV-K0X)
JC SPC560B60+95128 CAN (BSI04EV2-KEX)
VALEO 2M48H+24C128 CAN (BSIEV-X0X-00)
VALEO SC667152+95256 CAN (BSI-N0X)
Tap “Read PinCode” , then “All keys lost read”
Tab “Auto Identify” .
Tab “Continental BSI-QOX”.
Now you have PSA pin code and ready to program new keys with X300 Pro3 or X300 DP Plus.
PSAI2EMU : Peugeot Citroen IMMOBILISER IMMO DECODER and EMULATOR from 2001 – CAN
Smok: smok good for new psa cars and olds to, it have option to find pin for old kline siemens bsi to.
Abrites: abrites has proved to be excellent on can vehicles and reliable now on a lot of old kline too , really can’t fault abrites psa from read pin to code key.